https://wiki.strataggem.com/ 2026-05-09T12:57:13+00:00 https://wiki.strataggem.com/ https://wiki.strataggem.com/lib/exe/fetch.php?media=wiki:favicon.ico text/html 2021-04-04T13:12:21+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.strataggem.com/doku.php?id=products:flipper:adc_i2c_arduino&rev=1617541941&do=diff I2C communication with an Analog-to-Digital Converter : ADS1015 component ---------- tags: flipper, arduino, ADC, ADS1015, I2C This is an example of I2C communication with an ADC component. 1. Schematics For this example we used Sparkfun's ADS1015 Library. We are using the I2C1 communication bus so we will use Wire1 instance (if we were using I2C0 it would have been Wire instance, see text/html 2021-04-04T12:51:27+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.strataggem.com/doku.php?id=products:flipper:arduino_bus_references&rev=1617540687&do=diff Description of Flipper communication buses and their use in Arduino IDE ---------- tags: flipper, arduino, I2C, SPI, UART, USB 1. Names of the different bus instances for flipper board in Arduino Unlike a classic arduino uno board, the flipper has multiple instances of each communication bus. text/html 2021-04-06T08:02:50+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.strataggem.com/doku.php?id=products:flipper:arduino_use_gpio&rev=1617696170&do=diff Using GPIOs in Arduino with flipper board ---------- tags: flipper, Arduino, GPIO If you need to use a flipper GPIO in Arduino, you need to find the arduino name of the GPIO : To do so, use following table and check for the arduino name of the GPIO you want to use. text/html 2021-05-11T16:55:29+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.strataggem.com/doku.php?id=products:flipper:flash_stk&rev=1620752129&do=diff Flashing NRF52 with slstk2010a 1. Requirements 1.1 Hardware * slstk2010a : EFM8 Sleepy Bee (STK) * STK/WSTK Debug Adapter * 10-pin JTag Wires 1.2 Software * Simplicity Studio 5 * J-link Softare 2. Putting the STK in Debug Out Mode In Simplicity Studio 5 go to : Debug Adapters and select your STK (J-Link Silicon Labs (44 text/html 2023-11-03T13:30:16+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.strataggem.com/doku.php?id=products:flipper:flipper_product_family&rev=1699018216&do=diff Flipper 1. Product specifications * Vin: 4V-6.5V * LiPo battery charger included * Micro USB port for programming and charging 2. Common to Bare-Metal and Arduino * Flashing NRF52 with slstk2010a * Pinout of the Flipper 3. Use with Arduino SDK * Setup arduino development environment for flipper * Updating Strataggem's Arduino Board Support Package * Description of Flipper communication buses and their use in Arduino IDE 4. Example of Arduino code text/html 2021-04-04T13:16:36+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.strataggem.com/doku.php?id=products:flipper:gps_uart_arduino&rev=1617542196&do=diff UART Communication between the flipper and a GPS Module : Ublox SAM-M8Q ---------- tags: flipper, GPS, Ublox SAM-M8Q, Arduino, UART This is an example code of UART communication between a GPS Module and the flipper board. 1. Requirements Version 0.2.0 or higher of the Strataggem nRF52 arduino board package (see updating the bsp ). text/html 2023-01-11T09:14:07+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.strataggem.com/doku.php?id=products:flipper:pinout&rev=1673428447&do=diff Pinout of the Flipper ---------- tags : flipper, nrf52, pinout, schematic 1. Description Pinout Documentation generated with Graphical Datasheets 2. Top Side Pinout [flipper_top.svg] [SVG file of the pinout] 3. Bottom Side Pinout Header male side. pin 1 of the header is at the bottom right corner text/html 2021-11-18T09:34:42+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.strataggem.com/doku.php?id=products:flipper:setup_arduino_development_environment_for_flipper&rev=1637228082&do=diff Setup arduino development environment for flipper ---------- tags: flipper, arduino, setup, IDE, development 1. Requirements The Flipper board must be powered on. The board is power by * branch the USB of the PC to the flipper USB * either text/html 2021-04-04T13:12:45+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.strataggem.com/doku.php?id=products:flipper:si70_i2c_arduino&rev=1617541965&do=diff I2C Communication with a temperature/humidity sensor : SI7021 ---------- tags: flipper, arduino, si7021, I2C This is an example code of I2C communication between a temperature/humidity sensor and the flipper board. The temperature/humidity sensor in the example is a text/html 2021-04-04T13:12:36+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.strataggem.com/doku.php?id=products:flipper:sps30_i2c_arduino&rev=1617541956&do=diff I2C Communication with the particule sensor : SPS30 ---------- tags: flipper, I2C This is an example code of I2C communication between a particulate matter sensor and the flipper board. The particulate matter sensor is a [Sensirion SPS30]. The sensor is wired on I2C1 communication bus so we will use Wire1 instance (if we were using I2C0 it would have been Wire instance, see text/html 2021-04-04T12:26:57+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.strataggem.com/doku.php?id=products:flipper:update_arduino_bsp&rev=1617539217&do=diff Updating Strataggem's Arduino Board Support Package (BSP) ---------- tags: flipper, arduino, update, BSP, board support package Regularly we will be adding new features to Strataggem's Arduino Board Support package. This features will be included in new versions of the BSP. text/html 2021-04-04T12:31:56+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.strataggem.com/doku.php?id=products:flipper:using_sd_card_arduino&rev=1617539516&do=diff SD Card arduino support for flipper boards ---------- tags: arduino, flipper, SD card Using SdFat Library For the flipper board we are using two SPI instances : SPI and SPI1. SPI1 is hardware attached to the SPI card. However the basic SD Arduino Library is fixed with instance SPI.