Differences

This shows you the differences between two versions of the page.

--- products:lorawan_gateways:ecosignal:general_ecosignal_doc [2023/04/20 06:05] – manu
+++ products:lorawan_gateways:ecosignal:general_ecosignal_doc [2024/02/12 14:41] (current) – [4.2 Factory reset of the binary and the provisioning data] manu
@@ Line 12: / Line 12: @@
 ----
-===== - WiFi Setup =====
+===== - Configuration Manual Setup =====
-  * {{:products:lorawan_gateways:ecosignal:stghw_00054_lora_micro_gateway_wifi_setup_fr.pdf|}}
+In this documentation you can find all the information to setup your gateway (Wi-Fi, LoRa server, etc.)
+  * {{ :products:lorawan_gateways:ecosignal:stghw_00054_lora_micro_gateway_manual_en.pdf |english manual}}
+  * {{ :products:lorawan_gateways:ecosignal:stghw_00054_lora_micro_gateway_manual_fr.pdf |Manuel en Français}}
 ----
@@ Line 21: / Line 23: @@
 ==== - Configure the ecoSignal Gateway for the TTN LoRaWAN server ====
+There are 4 steps:
+  - put your gateway in configuration mode
+  - change the parameters of the LoRa server connection
+  - update your frequency plan to match the TTN plan
+  - put your gateway back in normal mode
+Each step is detailed below.
 === - Put the gateway in configuration mode ===
@@ Line 46: / Line 56: @@
   - upload your frequency plan that you use with TTN.
     - Click the button ''Choose file'' at the bottom of the page
-    - A default json configuration is provided below (you can download the file by clicking on its name, in blue below).
+    - A default json configuration for EU-868 is provided below (you can download the file by clicking on its name, in blue below).
 <file json Sx1302_configuration_TTN.json>
 {
@@ Line 234: / Line 244: @@
 You can upload the file using the interface shown at the bottom of the configuration page (an illustration is given below):\\
 {{ :products:lorawan_gateways:ecosignal:upload_new_frequency_plan.png?1200 |}}
+**DO NOT FORGET TO SAVE**
@@ Line 241: / Line 253: @@
   - Once you have saved all your changes
   - Go back to normal mode by pressing one time on the user button
-  - If every things is correctly configured, your gateway LED should show a steady GREEN
+  - If every things is correctly configured, your gateway LED should show a solid GREEN
+----
+===== - Factory reset for Debug version =====
+==== - Factory reset of the binary ====
+When programming the gateway or another esp32 chip on the your PC, while your gateway is plugged-in, you might flash a wrong firmware or a faulty firmware on your gateway.
+If you need to reflash a correct firmware here are some firmwares you can use:
+  * {{ :products:lorawan_gateways:ecosignal:stg-micro-lora-gw.bin | USMB EcoSignal Firmware 0.1.11-usmb}}
+  * {{ :products:lorawan_gateways:ecosignal:stg-micro-lora-gw_0.2.1-lyon1.bin | Lyon1 EcoSignal Firmware 0.2.1-lyon1}}
+You can use the ''esptool.py'' tool from espressif with the following command:
+<cli>
+esptool.py write_flash 0x0 stg-micro-lora-gw_0.2.1-lyon1.bin
+</cli>
+==== - Factory reset of the binary and the provisioning data ====
+You need to download:
+  - the partition configuration file (below) mfg_config.csv
+  - the security certificates of your gateway on https://pucs.wavebricks.com
+    - the device certificate (device.crt)
+    - the device private key (device.key)
+  - the json configuration file
+<file csv mfg_config.csv>
+key,type,encoding,value
+mfg_ns,namespace,,
+cert,file,binary,device.crt
+priv_key,file,binary,device.key
+ca-ota-cert,file,binary,ca_ota.crt
+json_conf,file,binary,conf.json
+</file>